Hello guys and gals! This community has been a wonderful wealth of knowledge and now I need a bit more!
I have winterized my whole camper except 3 places which is really confusing me… when I picked up the camper a few years back, the guy explains it all to me and I took good notes. I never asked questions before because I didn’t know what to ask and I would typically take my camper in for winterizing amongst other ‘warrantied repairs’ every year. This is the first year I’m doing it myself.
I have a fresh water pump and bypass on board (see picture) so I shut the freshwater line and open the ‘antifreeze line’ (A) and pump through each faucet and low point etc (bypassed water heater…yes drained that too). All is well and pink. What I don’t understand is the below!!!
1) how do I ‘winterize’ the city water line?(from outside camper) Do I just pour antifreeze down it? I don’t have a hand pump.
2) same question above for the black wash line. It’s on the outside but I’m unsure how to winterize that?
3) I released all freshwater from freshwater tank, but the line that goes from freshwater tank to the freshwater bypass line/antifreeze line’ needs winterizing too no? How do I get that and the freshwater tank winterized? I feel when I shut the bypass off, everything before it (to the downward left from arrows) won’t get antifreeze. Am I right in thinking that way?
4) same kind of question as number 3. When I bypass the water heater, there is a cold and hot line going TO the hot water heater obviously, but pumping antifreeze will winterize those too right? Like the liquid will find it’s way to the shut off point and go backwards as it’s blocked yes?
4) see picture one again. Am I supposed to leave the water bypass line closed all winter and then open again in spring? When I use city water, should that bypass be closed? Or open?
Other than that I think I got everything… I appreciate everyone’s help!!!
Sorry if these questions are dumb.
-
As mentioned by bb0730, you pop off the screen and press the little button in the middle until pink squirts out. Stand to the side, it will spray pretty far, not just trickle. I learnt that lesson the hard way the first time I did it.
-
You don’t need to winterize the black tank flush line, it doesn’t hold water, but if you’re really concerned, if you have an outside shower or spray port, you can connect it to the black tank flush and then pump pink through it like that. But like I said, it doesn’t hold water so whatever you pump will just end up in the tank anyway.
2b) Speaking of which, make sure you ran antifreeze through your spray port if you have one. You might remember the outside shower since it has handles like the taps inside, but the spray ports get overlooked.
-
The water in the line from the freshwater to the pump should have fallen out by gravity, so again, no need to winterize it.
-
When you bypass your hot water, there isn’t a long run between the bypass and the hot water tank. When you drained your hot water tank, gravity should have drained out whatever was in the little 2-3 inches of line that was there.
-
Your call on when to switch it, either now or in the spring. Just make sure to note it, and to do it the same way every year so you don’t get confused in the spring, trying to remember whether you did or didn’t flip in the preceding fall.
-
Bonus: Also don’t forget about the toilet. That’s another one people tend to miss, again, possibly due to the lack of handles.
This short video walks you through all the steps of winterizing. https://youtu.be/e8SY7P8Fm5I
For the city water line: there’s a back-flow preventer at the inlet. Remove the small filter screen from the city water inlet. With the pump pressurized, you can press in that back-flow preventer with a finger or a screw driver and pink will come out of the city water inlet.
I used a compresser and red pop, so I was a little less worried about the line between the pump and the fresh water tank, but…from my understanding, if there WAS any water in that small line and it DID freeze, because water expands when it freezes, it would expand into the large space of the fresh water tank. We did detatch that small line and blow through it and there was no water in there at all.
SOME people put red-pop in the fresh tank and pump it through the system that way, but some complain of the subtle taste it leaves.
For the line to the hot water tank after the bypass: with the pump pressurized with red-pop, I crack open those bypass lines very quickly to allow a splash of water into those lines. I’ll flush out the hot water tank in the spring for the small amounts of pink in there.
Disclaimer: I’m also relatively new at this and even vet campers will get it professionally done so they have peace of mind.
Thank you for all of this info!
I did just do the city line. Anti freeze came out that’s good.
So fresh water and black tank wash should be good
Too then! I appreciate all the help.
Do yourself a favour. Go buy the fitting that enables you to to hook up your air compressor to your city water connection. This allows you to hook up 30-40PSI air pressure and blow out all the lines prior to introducing antifreeze. It’s a cheap part and guarantees your antifreeze won’t be diluted. Also, make sure to pour antifreeze down your sink drains and toilet. Also, DONT FORGET THE OUTSIDE SHOWER if you have one and don’t forget to flush the toilet to get antifreeze through the toilet plumbing as well. A TON of people forget the last 2 items.
Purchase a 12v bilge pump and fill a bucket with your antifreeze. Cut a piece of garden hose that will spin on to your city connection. Attach hose to pump and turn it on. You can do the entire RV like this
Source: Winterizing question! 3 year owner, first time winterizer 🙂


